2008 Ford Edge Lug Nut Torque & Bolt Specs

The 2008 Ford Edge lug nut torque is 100 ft-lbs (135 Nm), tightened with a 19mm hex socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 100 ft-lbs (135 Nm) · Socket size: 19mm hex · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2008 Ford Edge. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Ford lug-nut torque varies more by chassis than most makes — 100 ft-lbs for Focus/Fusion/Fiesta, 150 ft-lbs for half-ton F-150, and 165 ft-lbs for Super Duty F-250/F-350. F-150s from 2004-2014 use a 21mm OEM socket, while 2015+ aluminum-body trucks moved to the larger 22mm. Ford torque-to-yield (TTY) head bolts are standard from the early 2000s — do not reuse them, ever.

Common fastener categories on the 2008 Ford Edge

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2008 model-year work: Always use a calibrated torque wrench for safety-critical fasteners, and replace lock washers and crush washers on every reassembly.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2008 Ford Edge?

The OEM-specified lug-nut torque for the 2008 Ford Edge is 100 ft-lbs (135 Nm), using a 19mm hex socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2008 Ford Edge lug nuts?

The 2008 Ford Edge uses a 19mm hex socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2008 Ford Edge fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Ford Edge years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2008 Ford Edge oil drain plug torque & size

→ 2008 Ford Edge suspension & steering torque specs (control arm, ball joint, tie rod)

All 20 2008 Ford Edge fastener specs

Per-bolt torque, wrench size, and thread spec for the 2008 Ford Edge, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 4 of the 20 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Brakes — 2008 Ford Edge

Brake fasteners on the 2008 Ford Edge — caliper bracket, slide pins, and banjo bolt torque follow. Front caliper bracket bolt tightens to 98 ft-lbs (133 Nm), takes a 18mm driver, runs on M14 threads, located at the front knuckle. This figure is independently verified against OEM service data. The front caliper slide pin uses a 7mm hex drive on a M10 thread, torqued to 65 ft-lbs (88 Nm) at the front caliper. OEM-verified spec.

Engine — 2008 Ford Edge

Engine bolt-by-bolt torque for the 2008 Ford Edge, including the long block, valve covers, and intake. The spark plug uses a 9/16" (14mm) drive on a M14x1.25 thread, torqued to 13 ft-lb at the cylinder head. At the oil pan, the oil drain plug (3.5l v6) torques to 21 ft-lbs (28 Nm) (15mm drive, M12x1.75 thread). For the engine oil pan, plan for a 15mm hex tool on a M12x1.75 stud; final torque is 20 ft-lb (oil drain plug).

Drivetrain — 2008 Ford Edge

Drivetrain and driveline fasteners for the 2008 Ford Edge — axle, transmission, and differential plugs. At the front hub, the front axle hub nut torques to 258 ft-lb (32mm hex drive, M24 thread).

Electrical — 2008 Ford Edge

Electrical fasteners on the 2008 Ford Edge. For the engine block, plan for a 13mm tool on a M8 x 1.25 stud; final torque is 35 ft-lbs (48 Nm) (alternator bolts).

Wheel Hardware — 2008 Ford Edge

Wheel Hardware fasteners on the 2008 Ford Edge. Lug nut tightens to 100 ft-lbs (135 Nm), takes a 19mm hex driver, runs on M12x1.5 threads, located at the all wheels.

Engine - Valve Train — 2008 Ford Edge

Engine - Valve Train fasteners on the 2008 Ford Edge. The valve cover bolts uses a 8mm / 10mm drive on a M6 x 1.0 thread, torqued to 89 in-lbs (10 Nm) at the cylinder head.

Wheels & Tires — 2008 Ford Edge

Wheels & Tires fasteners on the 2008 Ford Edge. At the wheels, the wheel lug nuts torques to 100 ft-lbs (136 Nm) (19mm drive, M14 x 1.5 thread).

Suspension - Struts — 2008 Ford Edge

Suspension - Struts fasteners on the 2008 Ford Edge. For the strut tower, plan for a 13mm tool on a M8 x 1.25 stud; final torque is 26 ft-lbs (35 Nm) (strut mount nuts (upper)). Strut to knuckle bolts tightens to 184 ft-lbs (250 Nm), takes a 21mm / 24mm driver, runs on M16 x 2.0 threads, located at the knuckle.

Drivetrain - Transmission — 2008 Ford Edge

Drivetrain - Transmission fasteners on the 2008 Ford Edge. Transmission pan bolts tightens to 106 in-lbs (12 Nm), takes a 8mm driver, runs on M6 x 1.0 threads, located at the transmission case.

Suspension - Shocks — 2008 Ford Edge

Suspension - Shocks fasteners on the 2008 Ford Edge. The rear shock lower bolt uses a 18mm drive on a M12 x 1.75 thread, torqued to 85 ft-lbs (115 Nm) at the control arm. At the body mount, the rear shock upper bolts torques to 52 ft-lbs (70 Nm) (15mm drive, M10 x 1.5 thread).

Brakes - Front Calipers — 2008 Ford Edge

Brakes - Front Calipers fasteners on the 2008 Ford Edge. At the caliper bracket, the front caliper guide pin bolts torques to 65 ft-lbs (88 Nm) (7mm hex drive, M8x1.0 thread). OEM-verified spec. For the knuckle, plan for a 18mm tool on a M14x2.0 stud; final torque is 98 ft-lbs (133 Nm) (front caliper bracket bolts). Confirmed against manufacturer service literature.

Engine - Ignition — 2008 Ford Edge

Engine - Ignition fasteners on the 2008 Ford Edge. For the cylinder head, plan for a 5/8" (16mm) tool on a M14 x 1.25 stud; final torque is 11 ft-lbs (15 Nm) (spark plugs).

Engine - Intake — 2008 Ford Edge

Engine - Intake fasteners on the 2008 Ford Edge. Intake manifold bolts tightens to 89 in-lbs (10 Nm), takes a 8mm driver, runs on M6 x 1.0 threads, located at the cylinder head.

Engine - Cooling — 2008 Ford Edge

Engine - Cooling fasteners on the 2008 Ford Edge. The water pump bolts uses a 8mm drive on a M6 x 1.0 thread, torqued to 89 in-lbs (10 Nm) at the block.

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2008 Ford Edge numbers above.

Loading the interactive 2008 Ford Edge fastener lookup with per-bolt filtering, part links, and torque tools…