2023 Honda Accord Lug Nut Torque & Bolt Specs

The 2023 Honda Accord lug nut torque is 80 ft-lbs (108 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2023 Honda Accord. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Honda's lug-nut torque sits at 80 ft-lbs (108 Nm) for nearly every passenger model from 1998 onward, with an M12x1.5 thread on most cars and the larger 14mm thread on Ridgeline and Pilot. The 19mm socket Honda uses is one of the only OEM oddities in the Japanese lineup — bring a 19mm with you, not just a 21mm. Honda factory torque values for engine oil drain plugs are unusually low (29 ft-lbs on most engines) and the crush washer is single-use, so replace it every oil change.

Common fastener categories on the 2023 Honda Accord

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2023 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2023 Honda Accord?

The OEM-specified lug-nut torque for the 2023 Honda Accord is 80 ft-lbs (108 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2023 Honda Accord lug nuts?

The 2023 Honda Accord uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2023 Honda Accord fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Honda Accord years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2023 Honda Accord oil drain plug torque & size

→ 2023 Honda Accord suspension & steering torque specs (control arm, ball joint, tie rod)

All 47 2023 Honda Accord fastener specs

Per-bolt torque, wrench size, and thread spec for the 2023 Honda Accord, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both.

Wheels — 2023 Honda Accord

Wheel and lug nut spec for the 2023 Honda Accord. For the wheel hub, plan for a 19mm tool on a M12x1.5 stud; final torque is 80 ft-lbs (108 Nm) (wheel lug nut).

Brakes — 2023 Honda Accord

Brake fasteners on the 2023 Honda Accord — caliper bracket, slide pins, and banjo bolt torque follow. Caliper bracket bolt tightens to 85 ft-lbs, takes a 14mm driver, runs on M12x1.25 threads, located at the steering knuckle.

Engine — 2023 Honda Accord

Engine bolt-by-bolt torque for the 2023 Honda Accord, including the long block, valve covers, and intake. The connecting rod bolt uses a 12mm drive on a M8x1.0 thread, torqued to Stage 1: 14 ft-lbs, Stage 2: +90° at the engine. At the cylinder head, the spark plug torques to 22 ft-lbs (16mm drive, M14x1.25 thread). For the turbo, plan for a 10mm tool on a M6x1.0 stud; final torque is 9 ft-lbs (turbo oil feed bolt). Oil filter housing tightens to 18 ft-lbs, takes a 24mm driver, runs on M20x1.5 threads, located at the engine block. The egr valve bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the manifold. At the cylinder head, the rocker arm bolt torques to 15 ft-lbs (12mm drive, M8x1.25 thread). For the engine, plan for a 10mm tool on a M6x1.0 stud; final torque is 9 ft-lbs (thermostat housing). Timing cover bolt tightens to 9 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the front cover. The oil drain plug uses a 17mm drive on a M14x1.5 thread, torqued to 29 ft-lbs at the oil pan. At the bracket, the alternator bolt torques to 18 ft-lbs (12mm drive, M8x1.25 thread). For the oil cooler, plan for a 17mm tool on a M12x1.5 stud; final torque is 22 ft-lbs (oil cooler line). Camshaft sprocket bolt tightens to 54 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the camshaft. The intercooler mount bolt uses a 12mm drive on a M8x1.25 thread, torqued to 16 ft-lbs at the frame. At the engine, the cylinder head bolt torques to Stage 1: 22 ft-lbs, Stage 2: +90°, Stage 3: +90° (14mm drive, M11x1.5 thread). For the valve cover, plan for a 10mm tool on a M6x1.0 stud; final torque is 7.2 ft-lbs (valve cover bolt).

Suspension — 2023 Honda Accord

Suspension and chassis fastener torque for the 2023 Honda Accord — strut, control arm, and sway bar values. At the subframe, the lower control arm bolt torques to 54 ft-lbs (17mm drive, M12x1.25 thread). For the sway bar, plan for a 14mm tool on a M10x1.25 stud; final torque is 29 ft-lbs (stabilizer link nut). Tie rod end nut tightens to 32 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the steering knuckle. The lower ball joint nut uses a 19mm drive on a M14x2.0 thread, torqued to 94 ft-lbs at the control arm.

Steering — 2023 Honda Accord

Steering linkage fasteners on the 2023 Honda Accord. For the bracket, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (power steering pump). Steering column u-joint tightens to 22 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the column.

Body — 2023 Honda Accord

Body fasteners on the 2023 Honda Accord. Active shutter bolt tightens to 7 ft-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the grille. The hood hinge bolt uses a 12mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the hood. At the frame, the front bumper bolt torques to 7 ft-lbs (10mm drive, M6x1.0 thread). For the body, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (fender bolt).

Exhaust — 2023 Honda Accord

Exhaust fasteners on the 2023 Honda Accord. The exhaust flange bolt uses a 14mm drive on a M10x1.25 thread, torqued to 33 ft-lbs at the manifold. At the various, the o2 sensor torques to 30 ft-lbs (22mm drive, M18x1.5 thread). For the cat flange, plan for a 14mm tool on a M10x1.25 stud; final torque is 33 ft-lbs (catalytic bolt).

Electrical — 2023 Honda Accord

Electrical fasteners on the 2023 Honda Accord. At the block/transmission, the starter support bracket bolt torques to 22 ft-lbs (12mm drive, M8x1.25 thread). For the block, plan for a 15mm tool on a M10x1.5 stud; final torque is 35 ft-lbs (belt tensioner pivot bolt). Starter solenoid terminal nut tightens to 70 in-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the solenoid. The alternator pivot bolt uses a 14mm drive on a M10x1.5 thread, torqued to See sequence at the bracket. At the block, the alternator support bracket bolt torques to 22 ft-lbs (12mm drive, M8x1.25 thread). For the tensioner body, plan for a 12mm tool on a M8x1.25 stud; final torque is 22 ft-lbs (belt tensioner lock bolt). Alternator terminal nut tightens to 70 in-lbs, takes a 10mm driver, runs on M6x1.0 threads, located at the alternator. The starter b+ terminal nut uses a 13mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the starter. At the block, the starter ground strap bolt torques to 8 ft-lbs (10mm drive, M6x1.0 thread).

Interior — 2023 Honda Accord

Interior fasteners on the 2023 Honda Accord. For the floor, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (center console bolt). Seat belt bolt tightens to 47 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the body. The seat track bolt uses a 14mm drive on a M10x1.25 thread, torqued to 29 ft-lbs at the floor. At the b-pillar, the seat belt anchor bolt torques to 32 ft-lbs (17mm drive, M12x1.25 thread).

Transmission — 2023 Honda Accord

Transmission fasteners on the 2023 Honda Accord. Trans mount bolt tightens to 54 ft-lbs, takes a 17mm driver, runs on M12x1.25 threads, located at the crossmember. The trans pan bolt uses a 10mm drive on a M6x1.0 thread, torqued to 8 ft-lbs at the trans pan. At the trans pan, the trans drain plug torques to 29 ft-lbs (14mm drive, M12x1.25 thread). For the trans case, plan for a 12mm tool on a M8x1.25 stud; final torque is 15 ft-lbs (shift cable bracket).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2023 Honda Accord numbers above.

Loading the interactive 2023 Honda Accord fastener lookup with per-bolt filtering, part links, and torque tools…