2024 Honda Accord Lug Nut Torque & Bolt Specs

The 2024 Honda Accord lug nut torque is 80 ft-lbs (108 Nm), tightened with a 19mm socket on M12x1.5 studs. Torque in a star pattern in two passes (snug, then final), and re-check after the first 50–100 miles of driving. Use a calibrated torque wrench — not an impact gun — for the final pass.

Lug nut torque: 80 ft-lbs (108 Nm) · Socket size: 19mm · Thread: M12x1.5.

This page is the OEM-referenced fastener summary for the 2024 Honda Accord. Use it before any maintenance or repair job where torque values matter — brake work, wheel changes, suspension service, engine teardowns, or oil changes. Specs are pulled from manufacturer service literature, cross-checked against community data, and updated as new chassis variants become available.

Honda's lug-nut torque sits at 80 ft-lbs (108 Nm) for nearly every passenger model from 1998 onward, with an M12x1.5 thread on most cars and the larger 14mm thread on Ridgeline and Pilot. The 19mm socket Honda uses is one of the only OEM oddities in the Japanese lineup — bring a 19mm with you, not just a 21mm. Honda factory torque values for engine oil drain plugs are unusually low (29 ft-lbs on most engines) and the crush washer is single-use, so replace it every oil change.

Common fastener categories on the 2024 Honda Accord

Wheel / lug nut torque and thread spec (covered above)
Brake caliper bracket bolts (typically 80-130 ft-lbs) and slide/guide pins (18-35 ft-lbs)
Engine oil drain plug torque — rarely above 30 ft-lbs; always use a new crush washer
Transmission pan, valve cover, and intake manifold bolts (low torque, often 89-106 in-lbs)
Suspension control arm, sway bar, tie rod end and ball joint torque
Spark plug torque (typically 10-15 ft-lbs on aluminum heads — do not exceed)
Differential cover bolts (RWD/4WD only) and transfer case fasteners

Repair guidance for this model year

For 2024 late-model work: Modern vehicles increasingly use aluminum body and suspension components. Aluminum fastener torque is typically 60-70% of equivalent steel torque, and aluminum threads strip easily. Use a calibrated torque wrench and apply anti-seize on any steel fastener threading into aluminum.

Tools you will need

Metric socket set (8mm-22mm), 6-point impact-rated
Calibrated torque wrench (10-150 ft-lbs covers most automotive jobs; add a 0-250 ft-lbs wrench for truck lug nuts)
Breaker bar (24" minimum) for initial loosening
Penetrating oil (PB Blaster or Kroil) for any fastener over 5 years old
Anti-seize on stainless or dissimilar-metal threads; thread-locker (Loctite blue) on critical reassembly

Frequently asked questions

What is the lug nut torque on a 2024 Honda Accord?

The OEM-specified lug-nut torque for the 2024 Honda Accord is 80 ft-lbs (108 Nm), using a 19mm socket on M12x1.5 thread studs. Use a calibrated torque wrench in a star pattern, in two passes (50% and 100%), and re-check after 50-100 miles of driving.

What socket size do I need for the 2024 Honda Accord lug nuts?

The 2024 Honda Accord uses a 19mm socket. A 6-point impact-rated socket is recommended over a 12-point chrome socket — 12-points round off lug nuts under impact-driver use.

Are the 2024 Honda Accord fasteners metric or SAE?

Metric is the standard for this vehicle. Most fasteners on this vehicle are metric (M6, M8, M10, M12, M14). Bring a full metric set; SAE substitutes can round the head. Bolt-head markings are the fastest way to confirm grade and material at the bench.

Other Honda Accord years

Same model, different model year — fastener spec may change. Always confirm against the year for your VIN.

→ 2024 Honda Accord suspension & steering torque specs (control arm, ball joint, tie rod)

All 24 2024 Honda Accord fastener specs

Per-bolt torque, wrench size, and thread spec for the 2024 Honda Accord, sourced from OEM service literature and verified against community shop data. Values pair imperial (ft-lb) and metric (Nm) where the manufacturer publishes both. 1 of the 24 fastener specs on this page are independently verified against OEM service manuals and manufacturer torque data (last reviewed June 2026).

Wheels — 2024 Honda Accord

Wheel and lug nut spec for the 2024 Honda Accord. Wheel lug nut tightens to 80 ft-lbs (108 Nm), takes a 19mm driver, runs on M12x1.5 threads, located at the wheel hub.

Brakes — 2024 Honda Accord

Brake fasteners on the 2024 Honda Accord — caliper bracket, slide pins, and banjo bolt torque follow. The brake line banjo bolt uses a 10mm drive on a M10x1.0 thread, torqued to 25 ft-lbs at the caliper.

Engine — 2024 Honda Accord

Engine bolt-by-bolt torque for the 2024 Honda Accord, including the long block, valve covers, and intake. At the engine block, the oil filter housing torques to 18 ft-lbs (24mm drive, M20x1.5 thread). For the front cover, plan for a 10mm tool on a M6x1.0 stud; final torque is 9 ft-lbs (timing cover bolt). Cylinder head bolt tightens to Stage 1: 22 ft-lbs, Stage 2: +90°, Stage 3: +90°, takes a 14mm driver, runs on M11x1.5 threads, located at the engine. The thermostat housing uses a 10mm drive on a M6x1.0 thread, torqued to 9 ft-lbs at the engine. At the block, the water pump bolt torques to 15 ft-lbs (12mm drive, M8x1.25 thread). For the oil pan, plan for the right driver on a M14x1.5 stud; final torque is 29 ft-lbs (39 Nm) (oil drain plug). OEM-verified spec. Oil cooler line tightens to 22 ft-lbs, takes a 17mm driver, runs on M12x1.5 threads, located at the oil cooler. The connecting rod bolt uses a 12mm drive on a M8x1.0 thread, torqued to Stage 1: 14 ft-lbs, Stage 2: +90° at the engine.

Suspension — 2024 Honda Accord

Suspension and chassis fastener torque for the 2024 Honda Accord — strut, control arm, and sway bar values. For the knuckle, plan for a 17mm tool on a M12x1.25 stud; final torque is 80 ft-lbs (wheel hub bolt). Stabilizer link nut tightens to 29 ft-lbs, takes a 14mm driver, runs on M10x1.25 threads, located at the sway bar. The tie rod end nut uses a 17mm drive on a M12x1.25 thread, torqued to 32 ft-lbs at the steering knuckle.

Steering — 2024 Honda Accord

Steering linkage fasteners on the 2024 Honda Accord. Power steering pump tightens to 15 ft-lbs, takes a 12mm driver, runs on M8x1.25 threads, located at the bracket.

Body — 2024 Honda Accord

Body fasteners on the 2024 Honda Accord. The hood hinge bolt uses a 12mm drive on a M8x1.25 thread, torqued to 16 ft-lbs at the hood. At the body, the door hinge bolt torques to 16 ft-lbs (14mm drive, M8x1.25 thread). For the body, plan for a 10mm tool on a M6x1.0 stud; final torque is 7 ft-lbs (fender bolt).

Exhaust — 2024 Honda Accord

Exhaust fasteners on the 2024 Honda Accord. At the cat flange, the catalytic bolt torques to 33 ft-lbs (14mm drive, M10x1.25 thread). For the manifold, plan for a 14mm tool on a M10x1.25 stud; final torque is 33 ft-lbs (exhaust flange bolt).

Electrical — 2024 Honda Accord

Electrical fasteners on the 2024 Honda Accord. For the bell housing, plan for a 14mm tool on a M10x1.25 stud; final torque is See sequence: 1) 22 ft-lbs 2) 43 ft-lbs final (starter mounting bolt). Idler pulley bolt tightens to 35 ft-lbs, takes a 15mm driver, runs on M10x1.5 threads, located at the bracket. The starter b+ terminal nut uses a 13mm drive on a M8x1.25 thread, torqued to 15 ft-lbs at the starter. At the block, the alternator support bracket bolt torques to 22 ft-lbs (12mm drive, M8x1.25 thread). For the solenoid, plan for a 10mm tool on a M6x1.0 stud; final torque is 70 in-lbs (starter solenoid terminal nut).

New to torquing wheels? Read our How lug nut torque works — the complete guide for star-pattern sequence, re-torque intervals, and how to read a lug spec — then use the 2024 Honda Accord numbers above.

Loading the interactive 2024 Honda Accord fastener lookup with per-bolt filtering, part links, and torque tools…