Kohler Courage Twin Engine Torque Specs

Cylinder head bolt torque at a glance

Every figure on this page is Kohler's own printed number except the cylinder head bolt. Kohler prints N·m first, then the inch- or foot-pound equivalent in parentheses. The head bolt is printed as 370 in-lb; the 30.8 ft-lb shown is our conversion. Where a row's note gives an ft-lb equivalent for an in-lb figure (oil pan fasteners, M8 muffler nuts, oil filter nipple), that is also our conversion.

This is the twin-cylinder Kohler Courage V-Twin, models SV710, SV715, SV720, SV725, SV730, SV735 and SV740 -- and the SV810, SV820, SV830 and SV840, which share the same service manual and torque table. Every figure below comes from Kohler's own service manual, form 32 690 01… Read the rest ›

Rev. I. The single-cylinder Courage SV470-SV620 is a different engine in a different manual, with lower head bolt torque (180 / 360 in-lb); it is covered on the main Kohler Engine Torque Specs page, not here. Kohler prints N·m first with the inch- or foot-pound figure in parentheses.

Where these numbers come from. 16 published figures, 0 confirmed gaps, every source named. How we checked ›

Every value on this page comes from Kohler's "SV710-SV740 / SV810-SV840 Service Manual," form 32 690 01 Rev. I, hosted at resources.kohler.com. One torque table covers every model in the manual; the engine is printed as 83 mm bore x 67 mm stroke, 725 cc (44 cu. in.). Page numbers cited are the manual's printed pages. Kohler: "Lubricate threads with engine oil prior to assembly." The cylinder head bolt is printed as 370 in-lb; the 30.8 ft-lb shown is our conversion of that figure. One real internal disagreement surfaced: the Style A oil pump screw row in the p.8 spec table misprints the new-hole value as "11.2 N·m (11 in. lb.)" -- 11.2 N·m is 100 in-lb, and the reassembly procedure on p.62 agrees, so 100 in-lb is shown with the conflict flagged. The SV620 is a single-cylinder engine covered by a different manual; do not use these values for it.

Every figure below is printed in a manufacturer's manual.

Kohler Courage SV710-SV740 V-Twin Manufacturer-published

series SV710, SV715, SV720, SV725, SV730, SV735, SV740 (the same manual and torque table also cover SV810, SV820, SV830, SV840)
From Kohler's official "SV710-SV740 / SV810-SV840 Service Manual," form 32 690 01 Rev. I, hosted at resources.kohler.com. More about this engine ›

One torque table covers every model in the manual; the engine is printed as 83 mm bore x 67 mm stroke, 725 cc (44 cu. in.). Kohler: "Lubricate threads with engine oil prior to assembly." Page numbers below are the manual's printed pages. Head bolts are 22.6 / 41.8 N·m (200 / 370 in-lb), the same as the Command CV V-Twin and KT7000 and higher than the Courage single SV470-SV620 (180 / 360 in-lb). The SV620 is a single-cylinder engine in a different manual; do not use these values for it.

Fastener Torque Where it comes from
cylinder head bolt (2-stage) 30.8 ft-lbStage 1: 22.6 N·m (200 in-lb) → Stage 2: 41.8 N·m (370 in-lb)
Final 41.8 N·m (370 in-lb); initial 22.6 N·m (200 in-lb). Why › The ft-lb figure is our conversion of the printed 370 in-lb. p.8 and reassembly p.75: "Torque screws in 2 stages; first to 22.6 N·m (200 in. lb.), then finally to 41.8 N·m (370 in. lb.), following sequence." 4 screws per head (8 total); the tightening sequence is a diagram in the manual and is not reproduced here.
connecting rod cap fastener 100 in-lb≈ 8.3 ft-lb
11.3 N·m. p.7: "Cap Fastener (torque in increments)"; reassembly p.70: "Torque screws in increments to 11.3 N·m (100 in. lb.)." The… Why › increments are not specified.
flywheel retaining screw 55 ft-lb
74.5 N·m. p.8; reassembly p.73: "Torque screw securing flywheel to crankshaft to 74.5 N·m (55 ft. lb.)." Same as KT7000; higher than the… Why › Command CV V-Twin (49 ft-lb).
spark plug 20 ft-lb 27 N·m. p.8. Gap 0.76 mm (0.030 in.), p.10.
crankcase oil drain plug 10 ft-lb 13.6 N·m. p.7: "Oil Drain Plug 13.6 N·m (10 ft. lb.)". Thread size not stated.
Show 11 more fasteners ›
FastenerTorqueWhere it comes from
oil pan fastener (10-screw sequence) 216 in-lb= 18 ft-lb
24.4 N·m (216 in-lb = 18 ft-lb, our conversion). p.8; reassembly p.71: "Torque fasteners in sequence shown to 24.4 N·m (216 in. lb)." The… Why › numbered 1-10 sequence is a diagram in the manual.
valve cover fastener 55 in-lb≈ 4.6 ft-lb 6.2 N·m. p.9; reassembly p.76: "Torque valve cover fasteners to 6.2 N·m (55 in. lb.), using sequence shown."
intake manifold mounting fastener (2-stage) 88 in-lb≈ 7.3 ft-lbStage 1: 7.4 N·m (66 in-lb) → Stage 2: 9.9 N·m (88 in-lb) Final 9.9 N·m (88 in-lb); initial 7.4 N·m (66 in-lb). p.8: "first to 7.4 N·m (66 in. lb.) finally to 9.9 N·m (88 in. lb.)".
rocker arm screw 100 in-lb≈ 8.3 ft-lb 11.3 N·m. p.8; reassembly p.75: "torque screws to 11.3 N·m (100 in. lb.)." The AVT rocker arm stud is also 11.3 N·m (100 in-lb), p.8.
rocker arm / valve adjustment setscrew (AVT) 70 in-lb≈ 5.8 ft-lb 7.9 N·m. p.8; reassembly p.75: "Torque setscrew to 7.9 N·m (70 in. lb.)." The jam-nut style adjuster is 7.3 N·m (65 in-lb), p.8.
muffler M8 hex nutsM8 216 in-lb= 18 ft-lb 24.4 N·m (216 in-lb = 18 ft-lb, our conversion). p.8. Also printed: 5/16-18 capscrew 16.9 N·m (150 in-lb); bracket screw 9.9 N·m (88 in-lb).
carburetor mounting nut 55–65 in-lb 6.2-7.3 N·m, printed as a band. p.7.
governor lever nut 60 in-lb= 5 ft-lb 6.8 N·m. p.8.
oil filter nipple (Style A oil pan only) 300 in-lb= 25 ft-lb 33.9 N·m (300 in-lb = 25 ft-lb, our conversion). p.8; reassembly p.71: "torque to 33.9 N·m (300 in. lb.). Do not overtighten."
oil pump screw, Style A 100 in-lb≈ 8.3 ft-lb⚠ sources disagree
11.2 N·m into new, as-cast holes; 7.3 N·m (65 in-lb) into used holes. p.62 reassembly: "11.2 N·m (100 in. lb.) in new, as-cast holes, or 7.3… Why › N·m (65 in. lb.) into used holes." CONFLICT: the p.8 spec table misprints the new-hole value as "11.2 N·m (11 in. lb.)"; 11.2 N·m is 100 in-lb, and p.62 agrees. Style B is 9.0 N·m (80 in-lb), p.8.
Oil Sentry pressure switch 40 in-lb≈ 3.3 ft-lb 4.5 N·m. p.9.

What is the head bolt torque on a Kohler Courage twin (SV730, SV740)?

Kohler's SV710-SV740 / SV810-SV840 service manual (form 32 690 01 Rev. I, p.8 and reassembly p.75) says to torque the screws in 2 stages, following the sequence: first to 22.6 N·m (200 in-lb), then finally to 41.8 N·m (370 in-lb), which is 30.8 ft-lb by our conversion. There are 4 screws per head (8 total).

What torque does the flywheel screw take on a Kohler Courage twin?

74.5 N·m (55 ft-lb), per the manual (p.8, reassembly p.73): "Torque screw securing flywheel to crankshaft to 74.5 N·m (55 ft. lb.)." That is the same as the KT7000 and higher than the Command CV V-Twin (49 ft-lb).

What are the oil drain plug and spark plug torques on a Kohler Courage twin?

The oil drain plug is 13.6 N·m (10 ft-lb), p.7. The spark plug is 27 N·m (20 ft-lb), p.8, with a gap of 0.76 mm (0.030 in.), p.10.

Does the Kohler Courage SV620 use these torque values?

No. The SV620 is a single-cylinder engine covered by a different Kohler manual, and the Courage single SV470-SV620 has lower head bolt torque (180 / 360 in-lb) than this twin's 200 / 370 in-lb. See the main Kohler Engine Torque Specs page for the single-cylinder engines.

Related lookups

Loading interactive lookup…